WALLTITE® injection insulation
Used to reduce the heat loss of existing and new build cavity walls. Installed as a liquid through a pattern of 12mm pre-drilled holes it expands within the cavity to gently fill each void eventually setting as a rigid polyurethane high-density insulation.
Features and benefits
- Low thermal conductivity
- Adds structural strength prolonging the life of the building
- Seamless airtight insulation system with no joints or gaps
- Applied throughout Ireland by BASF Foam Masters
- Fast & easy applied with no waste, minimum fuss and maximum effect
- No VOC’s, CFC’s, formaldehyde and has no harmful side effects
- Will not settle of sag and will last lifetime of building
- BASF polyurethane is certified to BS EN ISO 9001, ISO/TS 16949:2002 & BS EN ISO 14001.
- BBA & NSAI independently certified
- Class 1 fire rating.
Technical downloads
- WALLTITE Technical Guide
- WALLTITE data sheet: Cavity wall
- WALLTITE data sheet: Timber frame wall
- WALLTITE data sheet: Refurb masonry wall
Certification
WALLTITE® wall solutions
Cavity wall insulation
Certification
BBA Certificate No. 13/5002. WALLTITE® has undergone various performance tests. Certificates are available on request.Technical data
Specification | Full fill, closed cell, cavity wall insulation and stabilisation system |
NBS clause | F30, 10 and 150 P11, 50, 220, 230 and 24 |
Lambda 90/90 | 0.026 W/mK |
Closed cell content | 94.4% |
Adhesion to brick | 231k |
Typical U-values
Thickness of WALLTITE (mm) | U-value (W/m2K) |
---|---|
150 | 0.18 |
130 | 0.21 |
100 | 0.24 |
Preparation
Application
Timber frame insulation
WALLTITE foam insulation is spray applied directly between timber studwork onto the OSB at the required thickness. Ordinarily a 25mm cavity will remain between the insulation and vapour control layers to allow for services. WALLTITE guarantees additional support and stability for the whole of the timber frame construction. The resulting continuous insulation and air barrier system will provide a cleaner, healthier more comfortable environment. WALLTITE Polyurethane spray is hypo allergenic and so contains no fibres or dust and no noxious vapours. BASF WALLTITE is very quickly installed by Foam Master contractors sing specialist equipment.
Certification
BBA Certificate No. 11/4816. WALLTITE® has undergone various performance tests. Certificates are available on request.Typical detail
- Plasterboard and skim
- Vapour control layer to be lapped over DPC at floor level and returned to window reveal and jambs
- Unventilated air space
- Sheathing ply
- Breather membrane
- WALLTITE® CL100 insulation to achieve target U-value
- 50mm air gap
- Noggin to support plasterboard
- Sill plate
- DPC
- Treated timber cill support fixed to timber frame, clad and protected in DPC with insulation set above
Techincal data
Specification | Insulation sprayed between studwork |
NBS clause | P10 205A |
Lambda 90/90 | 0.025 to 0.028W/mK |
Fire rating | Class 1 to BS 476 Part 7 |
Adhesion to timber | 136kPa |
U-values
Thickness of WALLTITE (mm) | U-value (W/m2K) |
---|---|
135 | 0.20 |
100 | 0.25 |
90 | 0.27 |
Masonry wall insulation – steel stud
WALLTITE spray foam insulation can be applied directly onto a solid dry masonry wall, between steel studwork fixed floor to ceiling. This allows for a layer of WALLTITE to remain unbridged by studwork thereby helping to reduce u-values further. The foam will engage any light steel framework to provide a more solid, secure wall when compared to other insulation methods. Ordinarily a 25mm cavity will remain between the insulation and vapour control layers to allow for services. WALLTITE guarantees additional support and stability for the whole of the wall construction. The resulting continuous insulation and air barrier system will provide a cleaner, healthier more comfortable environment for any “hard to treat” home situation.
Certification
BBA Certificate No. 11/4816. WALLTITE® has undergone various performance tests. Certificates are available on request.Typical detail
- WALLTITE® CL100 insulation between and behind studwork to achieve target U-value
- Galvanised metal frame independent of the wall
- Unventilated air space
- 12.5mm vapour check wallboard and skim finish
Techincal data
Specification | Dry lining of solid masonry wall |
NBS clause | P10 |
Lambda 90/90 | 0.025 to 0.028W/mK |
Fire rating | Class 1 to BS 476 Part 7 |
µ | 61.12 |
U-values
Thickness of WALLTITE (mm) | U-value (W/m2K) |
---|---|
120 | 0.20 |
85 | 0.26 |
65 | 0.34 |
Masonry wall insulation – timber stud
WALLTITE spray foam insulation can be applied directly onto a solid dry masonry wall, between timber studwork either fixed directly to the wall or anchored floor to ceiling. The latter method allows for a layer of WALLTITE to remain unbridged by timber thereby helping to reduce u-values even further. Ordinarily a 25mm cavity will remain between the insulation and vapour control layers to allow for services. WALLTITE guarantees additional support and stability for the whole of the timber frame construction. The resulting continuous insulation and air barrier system will provide a cleaner, healthier more comfortable environment for any “hard to treat” home situation.
Certification
BBA Certificate No. 11/4816. WALLTITE® has undergone various performance tests. Certificates are available on request.Typical detail
- 25mm WALLTITE® behind studwork
- Treated timber studs set off by wall by brackets
- WALLTITE® CL100 insulation between and behind studwork to achieve target U-value
- Unventilated air space
- 12.5mm vapour check wallboard and skim finish
Techincal data
Specification | Dry lining of solid masonry wall |
NBS clause | P10 15A |
Lambda 90/90 | 0.025 to 0.028W/mK |
Fire rating | Class 1 to BS 476 Part 7 |
µ | 61.12 |
U-values
Thickness of WALLTITE (mm) | U-value (W/m2K) |
---|---|
120 | 0.20 |
85 | 0.26 |
65 | 0.34 |